How Do You Adjust A Car Back Up Camera

Download Commodity

A rear-view photographic camera, also known as a fill-in camera, lets you see what'southward backside your vehicle without having to look backwards. Though the device comes standard with many new car models, you can add together a rear-view camera to your vehicle if it didn't come with one.

1
Buy a mountable fill-in camera for your specific vehicle. For prophylactic, make certain you buy a device specifically designed to be a rear-view photographic camera. Purchasing one fabricated for your specific vehicle volition make information technology easier to install than a standard aftermarket camera. Then you tin install it easily, look for a photographic camera that mounts onto or directly behind your license plate.^[1]
- Look for backup cameras at consumer electronics stores.
2
Become an external monitor if you want to keep your existing rear-view mirror. An external fill-in monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they take up more space than internal monitors, external monitors are far easier to run into and can exist hands replaced if necessary.
- If you'd like, you can use a standard video monitor instead. Nonetheless, go along in mind that it may not have all the same features as devices designed for employ with backup cameras.
Advertisement
three
Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully functioning rear-view mirror that houses a small screen inside the drinking glass. Some internal monitors clip on top of your current rear-view mirror, but others replace your original mirror entirely.^[ii]
- Most internal monitors close off and disappear when not in use, making them a perfect option if you desire to preserve your motorcar'southward looks.
four
Purchase power and video cords if your camera and monitor didn't include them. For most rear-view camera installations, y'all'll demand camera and monitor splitter cords with connectors for video and ability cables, 2 bare wire power cables, and an RCA video cablevision.^[3]
- Most installation kits include these cables, but some may crave y'all to purchase them separately.
- Some camera models use wireless transmitters instead of standard video cables.

ane
Take off your rear license plate. Using a Phillips head screwdriver, remove each of the screws holding your rear license plate in identify. Then, pull the plate off and set it aside.^[four]
- Make sure you place the screws in a safe identify and so yous don't lose them.
2
Remove your trunk's interior panel. Popular open your trunk and wait for a solid interior panel covering the opposite side of your license plate mounting area. Then, insert a trim removal tool or other thin device behind the panel and pry it off.^[5]
- Removing this panel will betrayal the automobile's rear wiring chambers.
3
Drill a pocket-sized hole in the license plate mounting expanse. Make certain in that location are no obstructions between the license plate mount and the rear wiring chamber. Then, create a small hole in the car using a power drill equipped with a high-speed twist drill bit. Line upwardly your pigsty so it is directly behind where your photographic camera's power and video cable will get.^[vi]
- To figure out where to make the pigsty, hold your photographic camera up to the area you intend to mount it. Then, note the spot where its splitting cord sits.
- Create a hole that's large enough to fit your photographic camera's power and video cable.
- If you come across any obstructions, try to remove them. If you tin't, see if y'all tin brand a hole nearby.
- For near jobs, you'll need a drill chip that has a bore between ⁱ⁄₈ and ^ane⁄₄ in (0.32 and 0.64 cm).
four
Identify a safety grommet around your camera cablevision. Before running your photographic camera cable into the automobile, slip a safety grommet onto it virtually the not-splitting end. These small rubber washers, bachelor at most home improvement stores, will go along the wire in place and forbid leaks.^[7]
- Choose a grommet that's just large enough to fit within the drilled hole.
5
Run the camera cable into your body. Pull the splitting stop of your photographic camera's video and ability cable through the drilled hole into the trunk of your car. Make sure you lot pull information technology tight then the rubber grommet lodges into the drilled hole.
- Your photographic camera cable should run from the outside of the motorcar to the inside of the motorcar.
half dozen
Locate your car'south 2 reverse light wires. Reverse light wires are the cords that connect your car'south tail lights to the dashboard. They hook directly into your vehicle's tail lights and are normally located in the hatch or trunk of your car.
- These cords look different for every vehicle so, if yous can't find them, consult your possessor's manual for model specific data.
seven
Strip and divide your car's reverse low-cal wires. Using a wire stripper or pliers, peel back the rubber roofing the wires. And so, utilize a screwdriver or other thin tool to poke a hole through the center of each exposed wire, separating the individual wire strands.^[8]
- For safety, brand sure yous do this while the machine is turned off.
8
Fuse your camera wires with the reverse light wires. Attach 1 of your bare wire cables to the photographic camera cord's power connector. Then, poke your bare wires through the center of the exposed opposite light wires and twist them together. For safe, make sure you wrap the combined wires in electrical tape.^[9]
- Make certain you lot poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually blackness) bare wire through the negative reverse light wire.

Advertising

1
Road your camera'south video cablevision to the forepart of the motorcar. Connect your RCA cable to the camera cord'south video connector if necessary. Then, run it through your vehicle to the area by the fuse box. Depending on your vehicle model, you'll unremarkably be able to practise this by peeling back the automobile's headliner or side panels and pulling your cablevision through the exposed bedchamber.^[10]
- For certain trucks, you may demand to run the video cable through the vehicle'south frame runway.
- In most cars, yous'll find the fuse box underneath the steering wheel.
ii
Fix external monitors to the front windshield. If you're installing an external monitor, first attach your device's included mount to the windshield by following the manufacturer'south included instructions. And so, claw your monitor onto the mount.
- Nearly external monitors use a suction mount, though others may come with a more than complex mounting system.
3
Attach internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll demand to clip the new device onto your electric current rear-view mirror. For others, you'll demand to take off the mirror and slide your monitor into the pre-existing mirror mountain.^[11]
- Some internal monitors may come with their ain mounting system that you'll have to adhere to the car's front windshield.
four
Run the monitor's splitter cable to the fuse box. If necessary, hook your monitor's power and video cable into the device. Then, route the cable from the monitor to the area next to the fuse box.^[12]
- If you lot'd like, use a trim removal tool to pop out the headlining panel direct in a higher place your windshield. And then, run your cable through the exposed bedroom.
five
Connect your monitor'due south camera cable to the RCA cable. After routing your monitor's splitter cablevision, connect the video end of the cable to your camera's RCA string. And so, wrap the connected cords with electrical tape to concur them together.
- If your RCA and video cables accept the aforementioned ends, you may need to buy an RCA male to female converter cord. Yous can notice these at nigh electronic stores.
vi
Attach your monitor's power cable to a fuse tap. Connect your remaining bare wire cable to the fill-in monitor'due south power cord. Then, push the positive (commonly cerise) end of the bare wire cable into the open end of a fuse tap. Finally, crimp the two cables together with a pair of pliers.^[xiii]
- A fuse tap is a small cable that converts a blank wire into a fuse bespeak. You can find them at near machine part stores.
- If y'all'd prefer, you lot can leave the blank wire cable off and connect your camera'due south power cable to a cigarette lighter adaptor. And so, plug this adaptor into your car'due south cigarette lighter receptacle for power.
vii
Plug the fuse tap into the fuse box. Locate your fuse box and open information technology upwards. Then, plug your fuse tap into an open up fuse jail cell. If necessary, check your fuse box'south lid or your vehicle's instruction manual to see which slots are open.^[14]
- Afterward attaching your fuse, consider taping all your wires together using electric tape to get them out of the fashion.

Advertising

1
Connect your backup camera to its power and video cable. Return to the back of your car once yous've installed the rear-view monitor and all the necessary photographic camera cords. Close the body if necessary, and then connect the backup camera to its power and video cable.
- Your photographic camera's power and video cable should exist sticking out of the hole you drilled in the license plate mounting surface area.
ii
Mount the camera to your license plate. If the camera attaches to the front end of your license plate, prepare it to the plate by following the manufacturer'due south included instructions. If the camera attaches to the back of your license plate, line the device up with the plate's fastener holes and thread screws through them.^[fifteen]
- In nearly cases, you can attach a rear-view camera to the back of your license plate using the screws you removed from the car earlier.
3
Reattach your license plate and trim panels. Using a Phillips caput screwdriver, put your rear license plate dorsum on your vehicle. Once yous've reattached it, requite the license plate and backup camera business firm tugs to make sure they're secure.
- If y'all haven't already, reattach your automobile'due south interior torso console and other trim panels by pressing them back onto the vehicle.
four
Examination the camera to make sure everything works. Before using your new camera on public roads, test it in a rubber surface area like your driveway. If information technology turns on, place a large, durable object like a trash tin can behind the camera to run across how distorted the image is. If it does not turn on, read your installation transmission for troubleshooting information.
- In many cases, rear-view camera malfunctions are caused by loose or improperly continued wires.

Add New Question

Question

I hooked the photographic camera upwardly and it just flickers. Any communication?

You lot may desire to ensure all cables and connections are secured tightly. Double check that all connections are right. If this doesn't piece of work, check to see if the camera called is in good shape and isn't physically damaged.
Question

Suzuki installed opposite parking camera in my Swift Dzire Zxi. Only the camera shows upper view and not the ground below. What can I do ?

Brand sure that the photographic camera is installed the correct mode (not upside down), and bank check the position of the camera mounted. Take it back to the dealer that installed it and enquire them to check the alignment and fit.
Question

What is the best height for a reversing camera?

There is no optimal height for a back-up camera. The ideal height is based off the specific car or vehicle that yous have and your personal preferences, along with its intended application. Some back-upward cameras are placed on large service trucks and so that they tin can line up to trailer hitches easier, some are to preclude a blindspot on the route. Depending on your application, it can exist placed at any height. Most reversing cameras are a "wide view" fashion and the specific height location does not e'er affect the way it functions.
Question

So if I hooked up all the wires correctly but still no power, is it a fuse tap that I need to splice into the wires for it to work correctly?

Shannon Phillips

Community Answer

Cheque your world or ground it may be bad. Use your multimeter to come across if the ground is okay.
Question

Is information technology still okay to connect the back-up camera to the reverse lite with cars that have automobile lighting? Or, would I need to connect to the reverse wire on the gearbox?

Shannon Phillips

Community Respond

Yes, that will be fine, that how it is supposed to exist done. Expect for an auto electrician if yous need someone to call.

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertizing

Though most car dealers and mechanics will non install aftermarket backup camera systems, many audio and electronic shops will.

Brand sure you lot turn the car off before working with bare or stripped wires. If y'all demand to bear on exposed wires while the auto is on, put on a pair of shock-resistant rubber gloves.

Things Y'all'll Demand

Rear-view camera
Rear-view monitor
Connector cables
Phillips head screwdriver
Trim removal tool
Power drill with high-speed twist bit
Rubber grommet
Wire stripper or pliers
Electrical tape
Fuse tap

Well-nigh This Article

Commodity Summary Ten

To successfully install a rear-view camera, first remove your vehicle's rear license plate and interior trunk panel. Using a ability drill, dial a small hole through the exposed license plate mounting area and run your camera's power and video cord through it. Attach a bare wire power cablevision to your camera'south power connector, then strip your car'southward reverse low-cal wires and splice them with your bare wire power cable. To larn how to mount the rear-view camera and backup monitor, scroll down!

Did this summary aid you?

Thank you to all authors for creating a folio that has been read 261,682 times.